TQP9224 high linearity 0.25 w small cell pa data sheet march 1, 2018 | subject to change without notice - 1 of 8 - www.qorvo.com ? 14 pin 7 ? x ? 7 ? mm leadless smt package product features ? 2.3?C?2.4?ghz frequency range ? fully integrated, 3-stage power amplifier ? internally matched 50?? i nput/output ? ? 50 ?dbc aclr at pavg = +24 ?dbm ? 36.7 ?db gain ? 14% pae at +24 ?dbm ? 2 04 ?ma quiescent current ? on -chip control bias and temp. comp circuit ? rohs compliant ? covers band 30, 40 general description the TQP9224 is a high-linearity three-stage power amplifier in a low-cost surface-mount package with on-chip bias control and temperature control circuits, suitable for small cell or enterprise femto cell base station applications. the TQP9224 provides 36.7 db high gain and ?50 dbc aclr at +24?dbm linear power using a 20 mhz lte signal over the 2. 3? C ?2 . 4?ghz frequency range covering 3gpp bands 30, 40. the TQP9224 integrates three high performance amplifier stages to allow for a compact system design and requires very few external components for operation. the amplifier is bias adjustable allowing the amplifiers power consumption to be optimized for specific performance requirements. the TQP9224 is available in a lead- free/rohs- compliant 7?x?7?mm surface mount package. ordering information part no. description TQP9224tr13 2,500 pieces on a 13 reel (standard) TQP9224pcb401 2.3 ? 2.4 ? ghz evaluation board functional block diagram top view applications ? small cell?/?picocell ? enterprise femtocell ? customer premises equipment (cpe) ? data cards and terminals ? distributed antenna systems (das) ? booster amps, repeaters downloaded from: http:///
TQP9224 high linearity 0.25 w small cell pa data sheet march 1, 2018 | subject to change without notice - 2 of 8 - www.qorvo.com ? recommended operating conditions parameter min typ max units v cc1 , v cc2 +3.6 +4.5 +5.25 v v ref +2.75 +2.85 +2.95 v t case ?40 +85 c tj at t case max + 156 c electrical specifications are measured at specified test conditions. specifications are not guaranteed over all rec ommended operating conditions. absolute maximum ratings parameter rating storage temperature ?55 to +150?c rf input power, cw, 50, t=+25 ? c +9 dbm supply voltage (v cc ) 6 v v ref +3.5 v exceeding any one or a combination of the absolute maximum rating conditions may cause permanent damage to the device. extended application of absolute maximum rating conditions to the device may reduce device reliability. electrical specifications parameter conditions (1) min typ max units frequency range 2300 2400 mhz test frequency 2350 mhz gain 34 3 6. 7 40 db input return loss 16 db output return loss 8 db output p1db +33.6 dbm aclr p out = +2 4 dbm, 20?mhz lte e -tm1.1, 9.5 db par ? 50 - 45 dbc power added efficiency p out = +2 4 dbm, 20?mhz lte e -tm1.1, 9.5 db par 13 14 % spurious output level p out = +24 dbm, 10:1 vswr < 60 dbc vswr survivability no permanent degradation or failure 10:1 - quiescent current, i cq v cc1 + v cc2 1 60 2 04 250 ma reference current , i ref temp = ?40c to +85c, v ref = +2.85v 8.7 ma leakage current v cc = +4.5 v, v ref = 0 v 1.5 8 a operational current, i cc p out = +2 4 ?dbm 390 430 ma switching speed 0% vref to 90% rf rise time 1.7 2.5 s 10 0% vref to 10% rf fall time 0.87 1 s harmonics 2f 0 at +24dbm, cw signal - 40 - 35 dbc 3f 0 at +24dbm, cw signal - 54 - 49 dbc 4f 0 at +24dbm, cw signal - 61 - 56 dbc thermal resistance, jc module (junction to case) 35.4 c/w notes: 1. test conditions unless otherwise noted: v cc 1 ?=?v cc2 = +4.5 ? v, v ref = +2.85v, temp?=?+25?c, 50? system. downloaded from: http:///
TQP9224 high linearity 0.25 w small cell pa data sheet march 1, 2018 | subject to change without notice - 3 of 8 - www.qorvo.com ? evaluation board (TQP9224 ? pcb) bill of material ?C? TQP9224? pcb reference des. value description manuf. part number n/a n/a printed circuit board u1 n/a high linearity 0.25 w power amplifier qorvo TQP9224 r1 0 resistor, chip, 0603, 5% various c1 0.01 uf capacitor, chip, 0603, 5% various c11 100 pf capacitor, chip, 0603, 5% various c3, c9 0.1 uf capacitor, chip, 0603, 5% various c5, c14 10 uf capacitor , chip, 6032, 10%, tantalum various c6, c10 1000 pf capacitor , chip, 0603, npo/cog, 5% various 7 6 1 10 8 9 11 12 13 14 2 3 4 5 match match biasing circuit c5 10uf (6032) r1 0 ? j3 vcc1 c9 1.0uf c6 1000pf j5 vpd c1 0.01uf c11 100pf j1 rf input j2 rf output r2 dnp j6 vdet c13 dnp c12 dnp c3 1.0uf c10 1000pf c14 10uf (6032) j4 vcc2 downloaded from: http:///
TQP9224 high linearity 0.25 w small cell pa data sheet march 1, 2018 | subject to change without notice - 4 of 8 - www.qorvo.com ? performance plots test conditions unless otherwise noted: v cc1 = v cc2 = +4.5v, v ref = +2.85?v, i cq = 2 04 ma, i ref = 8.7ma , temp.=?+25?c 32 34 36 38 40 42 2300 2320 2340 2360 2380 2400 gain (db) frequncy (mhz) gain vs frequency vs temperature +85c +25c ?40 c -20 -15 -10 -5 0 2300 2320 2340 2360 2380 2400 |s11| (db) frequency (mhz) input return loss vs. frequency temp.=+25c -15 -10 -5 0 2300 2320 2340 2360 2380 2400 |s22| (db) frequency (mhz) output return loss vs. frequency temp.=+25c -60 -55 -50 -45 -40 -35 -30 16 17 18 19 20 21 22 23 24 25 26 aclr (dbc) pout (dbm) aclr vs pout vs frequency 2.30ghz_l 2.30ghz_u 2.35ghz_l 2.35ghz_u 2.40ghz_l 2.40ghz_u temp.=+25c lte 1 ch 20 mhz, adj ch ibw 18.02 mhz par 9.5 db no clipping -60 -55 -50 -45 -40 -35 -30 16 17 18 19 20 21 22 23 24 25 26 aclr (dbc) pout (dbm) aclr vs pout vs temperature -40c_l -40c_u +25c_l +25c_u +85c_l +85c_u freq = 2350mhz lte 1 ch 20 mhz, adj ch ibw 18.02 mhz par 9.5 db no clipping 30 31 32 33 34 35 2300 2320 2340 2360 2380 2400 p1db (dbm) frequency (mhz) p1db vs frequency +85c +25c ?40 c 0 5 10 15 20 16 17 18 19 20 21 22 23 24 25 26 pae (%) pout (dbm) efficiency vs pout vs frequency 2.30ghz 2.35ghz 2.40ghz temp.=+25c lte 1 ch 20 mhz, adj ch ibw 18.02 mhz par 9.5 db no clipping 0 5 10 15 20 16 17 18 19 20 21 22 23 24 25 26 pae (%) pout (dbm) efficiency vs pout vs temperature -40c +25c +85c freq = 2350mhz lte 1 ch 20 mhz, adj ch ibw 18.02 mhz par 9.5 db no clipping downloaded from: http:///
TQP9224 high linearity 0.25 w small cell pa data sheet march 1, 2018 | subject to change without notice - 5 of 8 - www.qorvo.com ? pin configuration and description top view pad no. label description 1 v ref sets the bias current for the amplifiers. it can also be used to power down the device. 2, 3, 6, 8, 9, 10, 13, 14 gnd rf and dc ground. 4 v cc 1 voltage supply for the active bias circuitry. 5 rf in rf input pin. the dc is internally blocked at this pin. 7 nc no internal connection. 11 v cc 2 dc voltage supply connection for amp1, 2, 3. 12 rfout rf output pin. the dc is internally blocked at this pin. backside paddle rf/dc gnd rf/dc ground. see pcb mounting pattern for suggested footprint. evaluation board pcb information qorvo pcb 11 26637 material and stack- up 50 ohm line dimensions: width = .028 spacing = .028. 1 oz. cu bottom layer nelco n-4000-13 core nelco n-4000-13 1 oz. cu top layer 1 oz. cu inner layer 1 oz. cu inner layer 0.062" 0.006" finished board thickness 0.014" 0.014" downloaded from: http:///
TQP9224 high linearity 0.25 w small cell pa data sheet march 1, 2018 | subject to change without notice - 6 of 8 - www.qorvo.com ? package marking and dimensions marking: part number C TQP9224 trace code notes: 1. all dimensions are in millimeters. angles are in degrees. 2. dimension and tolerance formats conform to asme y14.4m-1994. 3. the terminal #1 identifier and terminal numbering conform to jesd 95-1 spp- 012. pin 1 location a s aa a a a a a a a a a a a a s TQP9224 downloaded from: http:///
TQP9224 high linearity 0.25 w small cell pa data sheet march 1, 2018 | subject to change without notice - 7 of 8 - www.qorvo.com ? pcb mounting pattern notes: 1. all dimensions are in millimeters. angles are in degrees. 2. use 1 oz. copper minimum for top and bottom layer metal. 3. vias are required under the backside paddle of this device for proper rf/dc grounding and thermal dissipation. we recommend a 0.35mm (#80/.0135") diameter bit for drilling via holes and a final plated thru diameter of 0.25 mm (0.10) . 4. ensure good package backside paddle solder attach for reliable operation and best electrical performance. 0.175 pin 1 location a a s s aa a a a a a a a a a a a pin 1 location a a s s aa a a a a a a a a a a a recommended land pattern recommended land pattern mask downloaded from: http:///
TQP9224 high linearity 0.25 w small cell pa data sheet march 1, 2018 | subject to change without notice - 8 of 8 - www.qorvo.com ? handling precautions parameter rating standard caution! esd -sensitive device esd?C?human body model (hbm) class 2 esda?/?jedec js - 001 -2012 esd?C?charged device model ( cd m) class c3 jedec jesd22-c101f msl?C?moisture sensitivity level level 3 ipc/jedec j-std- 020 solderability compatible with both lead-free (260c max. reflow temp.) and tin/lead (245c max. reflow temp.) soldering processes. solder profiles available upon request. contact plating: electrolytic plated au over ni rohs compliance this part is compliant with eu 2002/95/ec rohs directive (restrictions on the use of certain hazardous substances in electrical and electronic equipment). this product also has the following attributes: ? product uses rohs exemption 7c-i to meet rohs compliance requirements ? halogen free (chlorine, bromine) ? antimony free ? tbbp-a (c 15 h 12 br 4 0 2 ) free ? pfos free ? svhc free contact information for the latest specifications, additional product information, worldwide sales and distribution locations: tel: 1-844-890-8163 web: www.qorvo.com email: customer.support@qorvo.com for technical questions and application information: email: appsupport@qorvo.com important notice the information contained herein is believed to be reliable; however, qorvo makes no warranties regarding the information co ntained herein and assumes no responsibility or liability whatsoever for the use of the information contained herein. all informatio n contained herein is subject to change without notice. customers should obtain and verify the latest relevant information before placing orders for qorvo products. the information contained herein or any use of such information does not grant, explicitly or implicitly, to any party any patent rights, licenses, or any other intellectual property rights, whether with regard to such information itself or any thing described by such information. this information does not constitute a warranty with respect to the products described herein, and qorvo hereby disclaims any and all warranties with respect to such products whether express or implied by law, course of dealing, course of performance, usage of trade or otherwise, including the implied warranties of merchantability and fitness for a particular purpose. without limiting the generality of the foregoing, qorvo products are not warranted or authorized for use as critical components in medical, life-saving, or life-sustaining applications, or other applications where a failure would reasonably be exp ected to cause severe personal injury or death. copyright 2018 ? qorvo, inc. | qorvo is a registered trademark of qorvo, inc. downloaded from: http:///
|
